Kabe de Luxe


Kabe de Luxe Kabe de Luxe Kabe de Luxe

Rectangular profile frame

High heel-friendly rollable scraping mat with naturally anodized square aluminium tubes combined with corrugated special black, red or grey rubber.

Kabe de Luxe is an enhanced form of the Kabe Mat Original for entrances where the need to accommodate high heels is combined with functionality. Kabe de Luxe is made on the same grounds as Kabe Mat Original but with square tubes combined with corrugated rubber strips to form a high heel-friendly surface. The mat can be rolled up and is double sided.

Available in both black (Original), red (Color) and grey (Color) rubber.

Kabe de Luxe should only be used indoors.


Kabe de Luxe is fully recyclable. Simply send worn out mats to us for recycling (See Contacts).
A detailed description of the contents can be downloaded via Contents declaration on the right.




Flexible entrances

Kabe de Luxe should be used indoors and is manufactured in rectangular shapes. If other shapes is desired we recommend the Kabe Original Mat.

Simply send a sketch or template, and we will produce to suit.


Surface treatment alternatives

Natural aluminium is standard but can also be provided in black or gold anodized aluminium
(NOTE! The photos show a Kabe Mat Original).


Natural aluminium

Gold anodized

Black anodized

Materials and construction

Aluminium alloy EN AW-6005-A-T6.
Dimensions: 12 x 12 x 1 mm.

A composition that is especially resistant to extreme temperature variation.
Black: EPDM 70° Shore.
Gray or Red: TPE 65° Shore.
Dimensions: 22 x 3.7 mm.

U 18 x 18 x 2 mm.

The mat is held together by Ø 2.3 mm stainless steel wire.

22 mm

Made to measure, max. size of a single piece 1740 x 5000 (A x B).

Approx 11 kg/m².

Natural aluminium is standard but can also be provided in black or gold anodized aluminium.

Brochures


Dimensions


A = Width | B = Length

Install Kabe de Luxe as follows:

Generally speaking, all types of mat should always be laid on a level, solid surface,

in a mat well edged with a casting frame Kabe 20R, Kabe 22R or otherwise on the floor in Kabe Ramp Frame type 2.

Always give measurements A = width and B = length with specifications and when ordering.


On existing floor
with incline or step

ZoomIn

If the mat lies on an incline or steps, it is best to insert studs in the floor or steps to prevent the mat from slipping.

On existing floor
- to prevent the risk of tripping

ZoomIn

Mats can be provided with Kabe Mat Ramp type 1 on the ends to prevent the risk of tripping.


On existing floor
- against doorsill or step

ZoomIn

If the mat lies against a doorsill or step, a Kabe Mat Ramp type 1 can be fitted to the front edge.

Recessed surface on existing floor
- mat ramp around the mat

ZoomIn

Kabe Mat Ramp type 2 on all four sides of the mat. The ramp is not attached to the mat and should be screwed to the floor if possible.


Recessed surface on existing floor
- against doorsill or step

ZoomIn

Kabe Mat Ramp type 2 can be placed on two or three sides if the mat lies against a doorsill or step. Ramps should be securely screwed to the floor.

In a mat well
- should be recessed 20 - 22 mm

ZoomIn

The mat should be recessed 20 - 22 mm. The Kabe casting frame is recommended to protect surrounding floor edges.


Existing mat well
- recess less than 20 mm

ZoomIn

If the recess is 15-19 mm deep, use Kabe Mat Original, height 18 mm. If a mat is placed in a well of less than 15 mm, fit Kabe special ramps at both ends.

Drainage in the mat well
- drain

ZoomIn

Kabe drains have an effective sand separator. With or without water trap.


Mats over drainage grids
- self-cleaning effect

ZoomIn

To achieve a self-cleaning effect, place the mat on a Kabe drainage grid in a deeper recess.


‌Maintain Kabe de Luxe as follows:

Kabe Mat Original is designed to remove sand and dirt from shoe soles as effectively as possible. It is also designed so that a large amount of sand or grit can lie in the mat without the mat appearing dirty.

Cleaning regularity, naturally, depends completely on the individual circumstances.

In much used entrances during the winter months with snow, grit, salt etc, the mat must be cleaned more often since excessive sand can become compacted and lift the mat out of the ramps or frame. This causes the mat to wear in an unnatural way.

No heavy lifting with Kabe Mat Original.

Kabe Mat Original need not be lifted out to remove sand and grit. Hook a steel wire with the lifting hook and fold up about 15 cm of matting. Then simply roll up the mat and remove the sand and grit with a vacuum cleaner of brush. Roll long mats half way from each end.

Kabe Mat Original = The double sided door mat!

The mat is designed with identical surfaces and should be reversed at least once a year, for maximum service life.

Maintenance

A strip may occasionally move slightly out of place when the mat is rolled up. This should then be pushed back into place immediately to prevent it being damaged. Deformed or broken strips can be repaired or replaced at our factory in Fjugesta.

NOTE! Do not use chemicals to clean the mat, only water.

Maintenance Instructions


Images per page:


Show Hide filter

Now showing:


File library


Brochures


Maintenance Instructions


Films

Download the film about Kabe Mat Original, Kabe Mat Original Serrated, Kabe Mat Original Color, Kabe de Luxe, Kabe Eco, Kabe Combi Mat och Kabex Special Grid.
Number of order: 1

Links